4 Things Wind Techs Need in FR

Wind turbine technicians need FR clothing that does three jobs at once. It has to carry an arc rating for the electrical work up tower, move freely through long ladder climbs, and hold up to kneeling and crawling inside a cramped nacelle. Regular workwear can't cover all of that, which is why more wind crews are choosing FR clothing designed around the climb itself.

MWG RIPGUARD Men's FR Wind Turbine Bib Overall in navy with yellow and silver reflective tape

The RIPGUARD™ Men's FR Wind Turbine Bib Overall, made for technicians and tower climbers.

Here's what to look for when you're choosing FR clothing for wind turbine work, and the gear our team built for it.

1. An arc rating that matches the electrical work

A wind turbine is a power plant on a stick. Between the converter cabinets at the base and the generator and switchgear up in the nacelle, you're working around serious electrical equipment on most service calls. That puts arc flash on the list of hazards right next to falls and confined spaces.

Your employer's hazard assessment sets the arc rating you need for each task, so start there. For everyday wind service work, a CAT 2 garment made from inherently flame resistant fabric is a common starting point. Inherent FR means the protection is built into the fibres, so it won't wash out over the life of the garment. If you want a refresher on how arc ratings work, our post on ATPV explained breaks it down.

2. Freedom to move on every rung

Climbing a tower is a full-body workout, and stiff gear makes every ladder feel longer. Look for FR clothing with stretch where your body bends and a cut that doesn't pull when you lift a knee to the next rung.

That's the thinking behind the MWG RIPGUARD™ Men's FR Wind Turbine Bib Overall. It's made with inherently flame resistant RIPGUARD™ fabric for dual-hazard protection against arc flash and flash fire, with a CAT 2 arc rating. Rib knit side panels give you stretch through the torso, a comfort crotch lets you take the ladder without fighting your gear, and the lightweight, breathable unlined build keeps you comfortable on the way up.

3. Pockets that stay shut up tower

Anything that falls out of a pocket at hub height becomes a problem for whoever is below. Zippered and flapped pockets matter more in wind work than almost anywhere else.

The bib has two zippered chest pockets, zippered cargo pockets with flaps, and webbing loops on the front for attaching locks, so the small stuff stays put. If you'd rather wear pants, the MWG RIPGUARD™ Men's FR Wind Turbine Work Pant brings the same idea with zippered holster pockets and cargo pockets with zippered flaps. It's also CAT 2 rated and meets ASTM F1506, NFPA 2112, and CSA Z96.

MWG RIPGUARD Men's FR Wind Turbine Work Pant in navy with zippered cargo pockets

The RIPGUARD™ Men's FR Wind Turbine Work Pant, a pant option for climbers who prefer a belt to suspenders.

4. Built for kneeling in tight spaces

Once you reach the nacelle, a lot of the job happens on your knees or sitting on steel. That's hard on fabric and harder on your joints.

Both the bib and the pant have knee pad pockets with hook-and-loop closures, so you can slide in pads for long service days and pull them out when you don't need them. Reinforced seat patches add durability where you sit and slide the most, and adjustable leg tabs keep the hems from catching on ladders and harness straps. Reflective tape on both pieces helps you stay visible at the base of the tower when light is low.

How do you layer for wind at height in winter?

The wind at hub height can feel a lot colder than the air on the ground, especially on a winter service call. Because the wind turbine bib and pant are unlined, they work as part of a layering system. Start with an FR base layer that wicks sweat from the climb, then add an FR hoodie on the colder days. Each piece you add should be flame resistant, and our layering guide shows how different MWG combinations come together.

You can see both pieces together in our wind energy collection. If your crew is setting up FR for a whole site, our team is happy to help you find the right fit.

 

Retour au blog